By Katja Kromann

How to: build a queen bed with twin trundle - IKEA hack

How to: build a queen bed with twin trundle - IKEA hack

This weekend I made some serious progress with B's room. I painted the bed and re-upholstered his headboard.

Here it is:

We originally built this bed a couple of years ago after I had tried to find a queen bed with a trundle without any luck. I thought it would be great with more sleeping space for guests or sleep-overs that B might have and it has seen plenty use.

We did run into a few problems, however, which we have now remedied. The first problem was that B had the great idea to jump in the bed one time too many. We originally built the T center post that holds the slats out of 1x3. Not strong enough for jumping... It eventually broke. The good news: everything else held up nicely :)

You can see the original T center post here:

So we beefed up the center post by going from 1x3 to 2x3. Much more solid. That, then gave us the problem that the trundle did not fit under the post any longer. I pondered my options for a while, then decided to have extensions put on the end boards, raising the overall height of the bed. I had my handyman do that part because I don't have a table saw.

Here you see the new end boards with the new wood attached at the bottom.


The end boards measure 61 3/4 x 18 ". If I had to build it again, I think I would make that 62 x 18 for just a tiny more room for the slats. The side boards are made of 1x6 pine with a 1x2 strip attached to hold the slats. Those boards are 80" long.

The last board for the right side as well as the board that is on the trundle is 9 inches tall. On the trundle we cut it down to 79" to have room to roll it under the bed.

The bed is assembled using these surface mounted bed rail brackets by Rockler.

As you can see I added brown felt on top of the wood that will hold the slats.

Here is the beefed up holder for the T post. A 1x4 with a notch to hold the T. We made it this way so that it is the bottom of the T that is supported, not just the top of the T.

> Here is the T post.

Here are the four pieces of the bed - held together by the brackets. This has held up really nicely. The brackets go together very sturdily. We did however add that fifth board on the right hand side (not pictured) to secure the bed to a square shape - instead of a diamond shape if you pushed on it.

I added felt to all the wood that would be touching wood to silence any squeaking.

Including on top of the center post. And YAY the trundle with mattress now fits under center post again.

We used some screws to hold the IKEA slats in place like this.

That's how we build the queen size bed.

On the Odda pull out bed we cut down the board so that the trundle would fit with our bed.

Then, we attached our own board and added a quarter round to finish off the raw edge from our cutting. Here is a picture of that after I primed the front of the trundle.

And here is a close-up of it after it's been painted.

We painted the bed Valspar's Lincoln Cottage to match the upholstery fabric for the tufted head board.

Both mattresses are from IKEA as well. For the trundle we got the Sultan Florvåg. It is just shy of 4 inches tall. For the queen bed we got the Sultan Fåvang. The Fåvang is the mattress B is sleeping on every night, so we went with one of the better quality mattresses that they have.

That's our IKEA hack.

Update: Some questions answered about this project

Next:  How to make a tufted headboard

Want more Ikea hacks:
Entertainment center with fireplace
Powder room turned full bath - Ikea vanity

#How-to #build a #queen #bed with #twin #trundle

Some blog posts contain affiliate links to products I use. More information
This article: How to: build a queen bed with twin trundle - IKEA hack first appeared on

Katja Kromann
About Katja Kromann

I am a Danish American decorating life in Seattle. I love all things design and DIY.

I can’t think of anything more fun than coming up with project, making it, photographing it and sharing it with you on my websites.

I am a Graphic Artist, a remodeller and home maker by day. My Portfolio
You might also be interested in these posts
How to: build a queen bed with twin trundle - IKEA hack is posted in the category |


We have been featured here

Full list here

We have been featured here

Full list here

Visit the other sites too
Privacy Disclaimer Contact